Elements Wanted
Six one l/i" head pins
two" 4 x one mm sterling silver rectangle wire Two one' items of sterling silver chain Two pearl beads
Two one.4 mm round sterling silver beads Two sterling silver ear wires
Applications Required
Ruler
Marker
Jeweler's observed or tin snips Safety glasses Tricky, flat floor Awl
Hammer /Ίί" drill bit
Handheld rotary Device, flex shaft, or drill push File
Fine grit sanding pad
Ring mandrel
Rawhide mallet
Two pairs of chain nose pliers
Wire cutters or tin snips
Round nose pliers
one.Use the ruler to measure and mark two Γ parts of 4 x one mm rectangle sterling silver wire.
two.Using a jeweler's noticed or tin snips, Slash the 4 x 1 mm rectangle sterling silver wire into two Γ lengths.
three.File Each and every conclusion from the 1" rectangle wire parts to remove any burs or rough edges; You may use the file to round the ends of your rectangle wire pieces If you need. Utilize a good grit sanding pad to go in excess of the region where you have filed to clean the sides and remove any file marks.
4.Utilize the ruler to measure and mark '/*’ from Each and every conclusion of the Γ pieces of rectangle wire and area a mark in the middle from the wire. This will likely be in which you drill the holes to slip the head pins by way of.
5Next, set on your security Eyeglasses! Then put the Γ rectangle wire pieces onto a tough, flat area. Place the point on the awl over the mark that you simply created /(." from Just about every end from the rectangle wire items, and utilize a hammer to firmly strike at the time on the top with the awl. This will make a pilot hole for drilling holes to the rectangle wire.
six.Employing a drill bit. drill holes into Each and every conclude of your rectangle wire pieces using a handheld rotary Resource, flex shaft, or drill push (though still sporting your security Eyeglasses!).
seven.Utilize the file or fine grit sanding pad to get rid of any burs or rough edges still left from drilling holes in the rectangle wire parts.
eight.Curve both Γ pieces of rectangle wire into a form utilizing a ring mandrel and rawhide mallet. If you don't have a hoop mandrel and rawhide mallet, use two pairs of chain nose pliers. Keeping one pair in Each and every hand, grasp Every single conclusion of your Γ rectangle wire piece in the chain nose pliers and gently bend the rectangle wire into a “C shape, aligning the holes which you drilled on Every single conclusion of your Γ rectangle wire parts. Compare each from the C-shaped rectangle wire items and alter the curves so that they're very similar in dimensions.
Established these apart.
nine.Utilize the ruler to measure the chain into Γ pieces. Use the wire cutters to cut the chain, and set these pieces aside.
10.Spot a head pin by way of a pearl bead after which incorporate one particular one.four mm sterling silver bead.
eleven.Utilize the ruler to evaluate and mark /t" earlier mentioned the best bead on The pinnacle pin. With wire cutters or tin snips, Slash The pinnacle pin wire Yu," above the top bead.
12.Using the chain nose pliers, bend the head pin wire next to the top bead at a 90-degree angle.
13.Hold the head pin Using the pearl bead and also the silver bead on it in one hand Using the wire that you simply bent pointing toward you. Using the round nose pliers, grip the end of the head pin wire that is pointing toward you and roll it away from you (think of turning the ignition key to start your car). Launch the pliers from The pinnacle pin wire. At this stage, the opening from the loop at the highest of The pinnacle pin wire really should be massive ample to slide the Γ size of chain on it just before closing the loop of The top pin. After you add the chain, use the spherical nose pliers to grasp the loop of The pinnacle pin wire and roll it shut. You should utilize the spherical nose or chain nose pliers to regulate the shape in the loop at the very best of the head pin if you need to.
fourteen.Repeat this move on men's jewelry the 2nd pearl and silver bead. Established these aside.
15.Location a head pin through the gap drilled into a person conclusion with the rectangle wire “C* form with the bottom or flat finish on the inside curve of the rectangle wire *C* condition. Utilize the ruler to evaluate and mark The top pin s/u.m over the rectangle wire. With wire cutters or tin snips, Reduce the head pin wire higher than the highest on the rectangle wire.
16.Use men's fashion rings the chain nose pliers to bend the head pin wire beside the rectangle wire in a 90-degree angle.
17.While using the chain nose pliers in a single hand, maintain the bottom or flat region of the head pin firmly men's fashion rings versus the rectangle wire with The pinnacle pin wire that you just bent pointing toward you.
With your other hand, men's designer rings & wedding bands utilize the spherical nose pliers to grip the tip of the head pin wire and roll it away from men's gold & silver rings you. Launch The top pin wire. At this time, the opening within the loop of The pinnacle pin wire really should even now be huge sufficient to slide the top backlink in the 1' chain onto iL Now increase the chain on the loop of The top pin. and after that utilize the spherical nose pliers to grasp the loop of The top pin wire and roll it closed. You may use the spherical nose or chain nose pliers to adjust The form with the loop at the very best of The pinnacle pin.
eighteen.Repeat this process on one other gap inside the C-shaped rectangle wire. In place of including the 1 * duration of chain With all the pearl and the sterling silver bead, increase the ear wire at the opposite stop. Slip the ear wire on to the loop of The top pin prior to closing the loop.
19.Repeat the preceding techniques on the next earring.
